manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 427

Test Results

Power Blazer

415

Alarms/Errors Overview

The following settings are available with Carrier Ethernet OAM test 
application.

Address Type

 defines the destination address type of the frame: 

Unicast

 or 

Multicast

 (default). 

Priority

1

 allows selecting the VLAN user priority: 

0

 (default) to 

7

. 

Refer to 

VLAN ID and Priority

 on page 758 for more information. 

Drop Eligible

1

 is set to 

No

 (no frames will be dropped when 

congestion occurs) and is not configurable. 

MEG Level

 (Y.1731 and MEF) is the Maintenance Entity Group 

Level configurable from 

0

 to 

7

 (default). 

Period

 determines the transmission period of frames: 

1 s 

(default) 

and 

1 min

. Not available with C-DCI. 

Amount

, only available with C-DCI alarm, is set to 

1

. 

Note:

The RDI alarm is available when the 

CC Function

 is enabled and is using 

the parameters from the CC Function (refer to page 271 for more 
information).

1. Available when VLAN is enabled (see 

VLAN

 on page 225). 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands