manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 453

Test Results

Power Blazer

441

Performance Monitoring

For 

M.2100 ISM

: Gives the count of the seconds within which 

anomalies (frame bit errors, CRC block errors, etc.) are 

 Y or at least 

one defect occurred. Y depends on the type of DSn/PDH signal as 
described in the following table. 

BBE

 (Background Block Error) (

G.826

, 

G.828

, 

G.829

, and 

M.2101

): 

Gives the count of Errored Block not occurring as part of a SES. 

Signal

SES Threshold

DS1 (SF)

8 frame bit errors (Near-End)

DS1 (ESF)

320 CRC-6 block errors (Near-End) 320 CRC-6 block errors (Far-End, if FDL 
enabled)

E1 (Framed without CRC-4) 28 frame bit errors (Near-End)

E1 (Framed with CRC-4)

805 CRC-4 block errors (Near-End) 805 E-bit errors (Far-End)

DS3 (M13)

2444 P-bit errors (Near-End) or 5 F-bit errors (Near-End)

DS3 (C-bit Parity)

2444 P-bit errors (Near-End) or 5 F-bit errors (Near-End) 2444 FEBE errors 
(Far-End)

E2 (Framed)

41 frame bit errors (Near-End)

E3 (Framed)

52 frame bit errors (Near-End)

E4 (Framed)

69 frame bit errors (Near-End)

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands