manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 555

Test Functions

Power Blazer

543

40/100G/400G Advanced - CFP4/CFP8/QSFP Control

CFP4/CFP8/QSFP Control Pins 

Allows the following transceiver control pin settings. Refer to the CFP MSA 
standard for more information. 

Note:

To apply any control, first select its check box then clear it; the control is 
applied only when the selected check box is cleared.

TX Disable

1

 check box (cleared by default).

Module Low Power Mode

 check box (cleared by default).

Module Reset 

check box (cleared by default). 

Module Power Shutdown

 check box (cleared by default).

CFP4/CFP8/QSFP Status Pins 

Gives the following transceiver’s pin status (refer to the CFP/QSFP MSA 
standard for more information): 

1. Not supported with QSFP. 

Transceiver

Pin status

CFP4
CFP8 

Module Absent

, 

RX Loss of Signal

, 

Global Alarm

QSFP

Module Absent

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands