manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 585

Test Functions

Power Blazer

573

Packet Capture

Trigger

Trigger Type

 defines the trigger source criterion that will be used to 

automatically start/stop the capture when a received frame matches 
the filter and the trigger criteria. 

Manual

 automatically starts the frame capture when the Capture 

button is on (green LED) and the test is started (refer to 

Start/Stop|TX Button

 on page 657). 

On Error

 starts the frame capture when the selected error occurs. 

FCS
Jabber
Oversize

 (Available when 

Oversize Monitoring

 is enabled)

Runt
Undersize
IP Checksum
UDP Checksum
TCP Checksum
Any Type

 (Any of the above errors).

Field Match

 starts the frame capture when the configured field 

match is encountered. User the 

Configuration

 button to select the 

field match criteria (see 

Filter Configuration

 from the 

Filters

 tab). 

Cfg. Status

 indicates the status of the configured field match 

configuration: 

Valid

 or 

Invalid

. A valid status is required to be able 

to start the capture. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands