manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 489

Test Results

Power Blazer

477

Summary (1588 PTP)

For both G.8265.1 and G.8275.1: 

Clock Class

 reports the description and code of the Grand Master 

Clock Class. 

Clock Mode

 reports the description of the Grand Master Clock 

Mode: 

Two-step

 or 

One-step

. 

Clock Accuracy

 reports the accuracy of the clock. 

Time Source

 reports the source of time used by the Grand Master 

Clock. 

Start Time

 indicates the time the test was started. 

Code 

Description

0-5, 8-12, 15-51, 53-57, 59-67, 123-132, 171-186, 188-192, 194-215, 
233-247, 249-254

Reserved

6

Sync to primary reference

7, 14

Holdover

13

Sync to application-specific reference

52, 58, 187, 193

Degraded

68 to 79, 81-109 (odd values), 11-122, 133-170, 216-232

Alternate PTP profiles

80-110 (even values)

a

a.

Refer to QL table on page 448 for the list of Quality Level values that will be used as the description.

Quality Level (QL-xxx

a

)

248

Default

255

Slave only

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands