EXFO Power Blazer 88000 Series User Manual Download Page 692

Page: 692 / 803

Glossary

680

88000 Series

Acronym List

dTE

dynamic Time Error High

DUS

Don’t Use for Synchronization

DUT

Device Under Test

E-VLAN

Extended Virtual Local Area Network

European standard for digital transmission-level 0 (64 Kbit/s).

European standard for digital transmission-level 1 (2.048 Mbit/s).

European standard for digital transmission-level 2 (8.448 Mbit/s).

European standard for digital transmission-level 3 (34.368 Mbit/s).

European standard for digital transmission-level 4 (139.264 Mbit/s).

Errored Block

EBS

Excess Burst Size

Error Count

ECN

Explicit Congestion Notification

ECT

ECN Capable Transport

EEC

Ethernet Equipment Clock

EFS

Error Free Second

eHEC

extension Header Error Check

EIR Excess

Information

Rate

EoE Ethernet

over

Ethernet

EoOTN

Ethernet over OTN

ERDI

Enhanced RDI

Errored Second

ESMC

Ethernet Synchronization Message Channel

ESF

Extended Superframe

ESR

Errored Second Ratio

ETag Extended

Tag

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands