manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 280

Test Setup - Test Configurator, Timer, and System

268

88000 Series

S-OAM and MPLS-TP OAM

S-OAM and MPLS-TP OAM Responder 

S-OAM Responder

 or 

MPLS-TP OAM Responder 

check box when 

selected (default) allows responding to LBM, LTM, DMM, LMM, and SLM 
valid messages (test running or not). LTM and SLM are only available with 
Ethernet OAM. Traffic statistics are also monitored (refer to 

Responder

 on 

page 535).

For S-OAM: A valid message must have its source MAC address matching 
the Peer MEP MAC address, destination MAC address matching either the 
unit port Unicast MAC address or a Multicast class 1 address, VLANs 
matching the unit port VLANs, and MEG/MD Level matching the local 
MEG/MD Level. Refer to 

Unicast/Multicast Addresses for Ethernet OAM

 on 

page 757 for more information.

For MPLS-TP OAM: A valid message must have its: destination MAC address 
matching either the unit MAC address, FF:FF:FF:FF:FF:FF, or 
01:00:5E:90:00:00; VLANs matching the unit port VLANs; MPL Labels 
matching the local MPLS Label Stack configuration, including GAL; MEG 
Level matches the local MEG Level. For the Loopback function, a valid 
message must also have its: MEP ID of the target MEP ID TLV matching the 
Local MEP ID or ID Sub-Type is 0x00 (Discovery); and MEP ID and MEG ID 
of the requesting MEP ID TVL, if present, matching respectively the Peer 
MEP ID and the Local MEG ID. 

Respond to... message

Respond with... message

LBM

LBR

LTM

a

a.

Only available with Ethernet OAM.

LTR

DMM

DMR

LMM

LMR

SLM

a

SLR

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands