manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 429

Test Results

Power Blazer

417

Analysis - MTIE/TDEV

Analysis - MTIE/TDEV 

From the 

Test

 menu, tap

 Results

, 

Analysis

, and the 

MTIE/TDEV 

tab. 

Graph 

Graphically displays the MTIE/TDEV values in function of the observation 
interval. The MTIE and TDEV masks are also displayed when supported by 
the selected standard. 

MTIE values and mask are displayed in pink.

TDEV values and mask are displayed in blue.

Mask

Allows the selection of an ITU mask used to validate MTIE/TDEV statistics 
(refer to Mask on page 338). 

Remove Offset 

Remove Offset

 check box when selected, subtracts the estimated 

frequency offset from the Time Error/Time Interval Error data used to 
calculate the MTIE/TDEV. It is preferable to set this setting before starting 
the test since changing this setting while the test is running will require 
some time for MTIE/TDEV recalculation. 

MTIE 

The 

MTIE

 check box when selected (default) reports MTIE values on the 

graph. The MTIE pass/fail verdict is displayed when enabled. 

TDEV 

The 

TDEV

 check box when selected (default) reports TDEV values on the 

graph. The TDEV pass/fail verdict is displayed when enabled. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands