manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 735

Glossary

Power Blazer

723

G.709 Optical Transport Network (OTN)

ODU Multiplexing 

The ODU multiplexer is a function that allows the multiplexing of ODU 
tributary signals into higher OTN signal rates.  The G.709 standard supports 
2 types of ODU multiplexer which can be classified as follows:

Legacy architecture is based on multi-stage architecture to bring an 
ODUk client to a higher OTN interface rate. This multiplexer is 
identified by Payload Type 20 (PT 20).

New architecture uses a single stage architecture to bring an ODUk 
client to any higher OTN interface rate. This method supports the 
ODUflex client signal. The multiplexer is identified by Payload Type 21 
(PT 21).

Note:

Refer to the OTN BERT

 on page 45

 or OTN-SONET/SDH BERT

 on page 47

 for 

the ODU multiplexing capabilities.

The multiplexing strategy is based on the concept of tributary slots, which 
is similar in concept to the SONET timeslot. The multiplexing of 4 ODU1 in 
one ODU2 is made by distributing the ODU1 structure in a repetitive 
sequence of 4 ODU2 Tributary slots, a similar strategy is used for ODU3 
multiplexing where the repetitive sequence is made of 16 ODU3 tributary 
slots, refer to G.709 standard for detailed information.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands