manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 484

Test Results

472

88000 Series

Summary

C&M

 indicates either the received (HDLC or Ethernet) or negotiated 

(Auto) C&M for Ethernet subchannel and HDLC rates in Mbit/s. A red 
background indicates either a C&M type mismatch or HDLC 
Rate/Ethernet subchannel mismatch. An arrow is displayed indicating 
which C&M Channel, Ethernet or HDLC, is selected following the 
negotiation process. 

Code Word

 (CW) indicates the transmitted and received Code Word 

count. 

Hyperframe

 indicates the transmitted and received hyperframe count. 

L1 Reset

, available when 

Remote Radio Head

 emulation mode is 

selected, indicates the number of times a request to reset the RRH 
interface was received. 

OBSAI 

Note:

Available with OBSAI Framed L2. 

Sync

 indicates the RX State Machine status: green for FRAME_SYNC, 

red for other states, or gray for pending. The TX and RX State Machines 
are also displayed. 

The pass/fail verdict is displayed when enabled. 

Code Word

 reports the count of code words transmitted and received. 

Message Group

 reports the count of message groups transmitted and 

received. 

Frame

 reports the count of frames transmitted and received. 

RP3 Peer Target Address

 indicates the RP3 Peer Target Address; 

indicates a mismatch when displayed in red. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands