manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 487

Test Results

Power Blazer

475

Summary (1588 PTP)

Negotiation Status

 

The status of the PTP Negotiation is displayed while in Unicast 
negotiation (available with G.8265.1 profile). 

Negotiation 

Status

Description

Background 

Color

a

a.

The gray background color is also used for a Link Down.

Request Granted

All the Signaling request types have been granted. 

Green

[Message type] 

Request Denied

The Signaling grant message has not been granted. 

Red

Session Canceled

The Grand Master has canceled the Unicast session.

Red

No Reply

No message is received from the Grand Master following 
transmission of 3 Signaling requests for a message type. 
Make sure that both IP address and Domain (refer to 

1588 PTP

 on 

page 132) of the Grand Master Clock are valid as well as the IP 
address of the unit’s port used to connect on the network (refer to 

Network

 on page 220).

Red

Pending

Unicast negotiation has started and no message has been received 
from the Grand Master. 

Gray

Inactive

The Unicast negotiation is not active. 

Gray

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands