EXFO Power Blazer 88000 Series User Manual Download Page 574

Page: 574 / 803

Test Functions

562

88000 Series

FDL - Performance Report Message



Performance Information

table, available when the

Report Content

button is selected, reports the time t0, t0-1, t0-2, and t0-3 for each PRM.

Time



represents the valid PRM message received in the last second of

measurement (bytes 5 and 6).



T0-1

represents the message one PRM ago (bytes 7 and 8).



T0-2

represents the message two PRM ago (bytes 9 and 10).



T0-3

represents the message three PRM ago (bytes 11 and 12).

PRM

: 5 < CRC Error Event



: Line Code Violation Event



: 10 < CRC Error Event



100

: Under study for synchronization

: 100 < CRC Error Event



319

: Controlled Slip Event



: CRC Error Event



320

: Frame Sync. Bit Error Event



: Severely-Errored Framing Event



: Payload Loopback Activated

: CRC Error Event = 1

: Reserved

: 1 < CRC Error Event



and

: One-second report modulo 4 counter.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands