manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 556

Test Functions

544

88000 Series

40/100G/400G Advanced - CFP4/CFP8/QSFP Control

CFP4/CFP8/QSFP MDIO/I2C Access Interface 

MDIO/I2C - Bulk Read 

Page Select

, available for QSFP I2C, allows selecting the I2C 

address page: 

0x00

 (default) to 

0xFF

. 

MDIO/I2C Start Address

 allows selecting the MDIO/I2C start 

address: 

0x0000

 (default) to 

0xFFFF

 (MDIO)/

0x00FF

 (I2C). 

MDIO/I2C End Address

 allows selecting the MDIO

/I2C

 end 

address: 

0x0000

 to 

0xFFFF

; default is 

0x00FF

. 

Bulk Read

 button reads and displays the data based on the 

specified MDIO range (MDIO/I2C Start Address to MDIO/I2C End 
Address). 

Save to CSV

 button allows saving the read MDIO/I2C’s addresses 

and data to a CSV file. 

Note:

The bulk read size is limited to 1024 addresses.

MDIO/I2C - Read/Write

MDIO/I2C Address

 allows selecting the MDIO/I2C address: 

0x0000

(default) to 

0xFFFF

 (MDIO)/

0x00FF

 (I2C). 

MDIO/I2C Data

 allows either selecting (write) or reading the 

MDIO/I2C data: 

0x0000

(default) to 

0xFFFF

 (MDIO)/

0x00FF

 (I2C). 

Read

 button reads the data of the specified 

MDIO/I2C Address

. 

Write

 button writes the specified 

MDIO/I2C DATA

 value to the 

specified 

MDIO/I2C Address

. 

CFP4/CFP8 TX Status 

Indicates the transceiver transmission status for each optical lane.  

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands