manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 251

Test Setup - Test Configurator, Timer, and System

Power Blazer

239

ODU Channels - Global

Defect

 allows choosing on which layer and defect the service 

disruption time test will be performed. Choices depend on the 
selected test path. 

Note:

The Service Disruption Time measurement supports a parent defect 
approach where the SDT measurement is triggered when the selected 
defect or a higher defect in the signal structure hierarchy is detected.  

No Defect Time (ms)

 represents the period without any defects before 

stopping SDT measurement: 

0.005 ms

 to 

2000 ms

 (default is 

300 ms

). 

Pass/Fail Verdict

 check box when selected (cleared by default) 

enables service disruption pass/fail verdict and allows setting the 
threshold value. 

SDT Threshold (ms)

 allows entering the SDT threshold value that will 

be used to declare the pass/fail verdict: 

0.001

 to 

299999.999 ms

 

(default is 

50

 ms). 

Layer

Defect

ODUk

LOFLOM, AIS

, 

OCI

, 

LCK

, 

BDI

, 

BIP-8

, 

BEI

OPUk

AIS

, 

CSF

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands