manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 267

Test Setup - Test Configurator, Timer, and System

Power Blazer

255

RFC 2544 - Subtests

RFC 2544 - Subtests 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, tap on the RFC 2544 

block. and on the 

Subtests

 tab. 

Allows the configuration of each enabled subtest. 

Throughput 

The objective of this test is to find the throughput of the device under test 
for which there is no frame loss. Starting at the specified maximum rate 
(

Max. Rate

), the rate converges towards the highest throughput without 

frame loss. The search is done with a halving/doubling method until a final 
value is reached. The test performs the number of trials defined (

Trials

). 

The throughput measurement is validated the number of times specified 
(

Validations

) for the predefined duration 

(Trial Duration)

. The 

Accuracy

 

and 

Acceptable Errors

 specify how precise the result must be. The test is 

performed for each defined frame size. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands