manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 457

Test Results

Power Blazer

445

Performance Monitoring

UAS

 (Unavailable Second): Gives the count of the seconds 

corresponding to the period of unavailable time that begins at the 
onset of 10 consecutive SES events, including these 10 seconds. A 
period of available time shall begin at the onset of 10 consecutive 
non-SES events, including these 10 seconds. 

ESR

 (Errored Second Ratio): Gives the ratio of the number of ES in 

available time to total seconds in available time during a fixed 
measurement interval. 

ESR = ES ÷ AS

SESR

 (Severely Errored Second Ratio): Gives the ratio of the number of 

SES in available time to total seconds in available time during a fixed 
measurement interval. 

SESR = SES ÷ AS

BBER

 (Background Block Error Ratio): Gives the ratio of BBE in 

available time to total blocks in available time during a fixed 
measurement interval. The count of total blocks excludes all blocks 
during SESs. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands