manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 439

Test Results

Power Blazer

427

Labels

Labels 

From the 

Test

 menu, tap 

Results

, and 

Labels

. 

Note:

Selecting a Label byte to be generated will automatically update the 
corresponding OH byte. Refer to 

OH - SONET/SDH

 on page 591 for more 

information. 

Labels

STS/AU Path (C2)

: The C2 byte is allocated to indicate the content of 

the STS SPE / VC, including the status of the mapped payloads. 

Received

: Displays the received C2 byte. Refer to 

C2

 on page 599 for 

more information. 

PLM-P/UNEQ-P

 / 

HP-PLM/HP-UNEQ

: Enables the Payload Mismatch 

and STS/AU UNEQ monitoring. This setting is coupled with the 
configuration of 

Labels

 on page 196. 

Expected

: Select the expected C2 byte from the list. Refer to 

C2

 on 

page 599 for more information. 

VT/TU Path (V5)

: The V5 byte is allocated to indicate the content of the 

VT/TU path, including the status of the mapped payloads. 

Received

: Displays the received V5 byte. Refer to V5 on page 602 for 

more information. 

PLM-V/UNEQ-V / LP-PLM/LP-UNEQ

: Enables the Payload Mismatch 

and VT/TU UNEQ monitoring. This setting is coupled with the 
configuration of 

Labels

 on page 196. 

Expected

: Select the expected V5 byte from the list. Refer to 

V5 

on 

page 602 for more information. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands