manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 622

Test Functions

610

88000 Series

Pointer Adjustment

Pointer Adjustment 

From the 

Test

 menu, tap 

Functions

, and the 

Pointer Adjustment 

tab. 

TX Pointer Adjustment 

Note:

Only available in 

Coupled

 topology.

The pointer adjustment supports two modes of operation: 

Manual

 and 

Sequence

. Both modes offer the generation of pointer events even when 

the test is not started. The Sequence mode is only available for SONET/SDH 
BERT test application for rates up to OC-192/STM-64. 

TX Pointer Adjustment - Manual Button 

Step 

Value

 

For STS/AU: Select the number of positive (Increment) or negative 
(Decrement) pointer adjustments to include into the STS-n (SONET) or 
AU-n (SDH): 

1

 (default) to 

1000

. For multiple pointer adjustments, the 

pointer adjustment rate is 1 adjustment at every 4 frames. 

For VT/TU: Select the number of positive (Increment) or negative 
(Decrement) pointer adjustment to include into the VTn (SONET) or 
TU-n (SDH): 

1

 (default) to 

1000

. For multiple pointer adjustments, the 

pointer adjustment rate is 1 adjustment at every 4 multiframes. 

Increment

 button sends the positive pointer adjustment defined. 

Decrement

 button sends the negative pointer adjustment defined. 

Pointer Value

 indicates the current pointer value. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands