manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 310

Test Setup - Test Configurator, Timer, and System

298

88000 Series

Signal - Signal Configuration (DSn/PDH)

RX

Apply Channel TX to RX

, available for decoupled test, allows applying 

the RX payload content based on the TX settings. 

None

 will be used 

when TX is set to either 

Idle

 or 

Tone

. For E0 the timeslots 0 and 16 

(PCM30 and PCM30 CRC4) are not configurable. Timeslot 0 processes 
the FAS/NFAS while timeslot 16 processes the Signaling frame. 

Note:

The RX timeslot selection is only configurable in a 

Decoupled

 topology 

when the 

Apply Channel TX to RX

 check box is cleared. A warning is 

displayed when the number of Pattern timeslot does not match between TX 
and RX. This is to ensure pattern continuity between the TX and RX 
interface in a MUX/DEMUX test even if used through a cross-connect device.

Select the payload content by tapping once or several times on each 
timeslot until the desired content appears.

Pattern

 (default) uses the pattern from the received signal. 

None

 does not use the pattern. 

Loopback button 

The Loopback feature generates a code that is interpreted by the DUT. 
The DUT interprets the command and implements the loopback.

Select the type of loopback that will be used to overwrite the traffic that 
will be generated. Choices are listed in the following table in addition 
with 10 predefined Loop Codes (see 

Modify Loop Codes button

 on 

page 299). 

Loopback Type

Command

Loop-Up

Loop-Down

CSU (10000/100)

10000 (default)

100

NIU FAC1 (1100/1110)

1100

1110

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands