manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 171

Test Setup - Test Configurator, Timer, and System

Power Blazer

159

EtherBERT, FC BERT, BERT (CPRI/OBSAI), and Unframed BERT

FC Frame 

Note:

Only available with FC BERT. 

Frame Size (Bytes)

 allows entering the frame size (in step of 4 bytes) for 

FC BERT test application: 

40

 to 

2148

 bytes (default). However the 

minimum frame size is 64 bytes when the 

Latency Tag

 check box is 

selected. 

Latency Tag Insertion 

Note:

Only available with FC BERT. 

Round trip latency measures the average round trip latency (delay) 
between the time the data was transmitted and received. 

Latency Tag 

check box when selected enables latency 

measurements.

Pass/Fail Verdict 

check box when selected enables the pass/fail 

verdict and allows setting the 

Round-Trip Latency Threshold

. 

Round-Trip Latency Threshold (ms)

 allows the selection of the round 

trip latency: 

0.015

 (default) to 

8000 ms

. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands