manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 234

Test Setup - Test Configurator, Timer, and System

222

88000 Series

Network

For 

IPv6

 the following configuration parameters are displayed: 

Link-Local 

IPv6 Address

, 

Global IPv6 Address

, and 

Default Gateway

. Tap on the 

Config

 button to access all settings. 

Link-Local IPv6 Address

 (LLA) is used for local communication 

between on-link neighbors and for Neighbor Discovery process. 

Mode

Stateless Auto

 (default) allows automatic generation of the IPv6 

address based on the MAC address. 

Static

 allows entering the IP Address. 

Address

, available with 

Static

 mode, allows selecting the 

Link-Local IPv6 Address. The accepted range is from 

FE80:0000:0000:0000:0000:0000:0000:0000

 to 

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF.

 The default address 

is

 FE80::[Interface ID]

, where [

Interface ID

] is generated from 

the source MAC address. When the 

Address

 field is selected for 

editing using virtual keyboard, the 

Previous IPs

 button appears 

allowing the selection of a previously configured IP address. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands