manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 472

Test Results

460

88000 Series

Service Configuration - Ramp

Service Configuration - Ramp 

From the

 Test

 menu, tap 

Results

, 

Service Configuration

, and the 

Ramp

 

tab. 

Service Name and Selection 

Service Name

 indicates the name of the selected service. Select the 

service to be displayed by either using the left/right arrow or by tapping 
over the service numbers area then tapping on a specific service number. 
An orange background indicates the selected service while a green 
background indicates the services that are enabled. 

Committed/Excess Steps 

Committed Steps

 indicate the pre CIR and CIR steps specified in the 

ramp configuration. 

Excess Steps

 indicate the 

CIR+EIR

 and 

Traffic Policing

 steps 

specified in the ramp configuration. 

Direction

, available with 

Dual Test Set

 or 

Dual Port

 topology, 

indicates respectively results from local to remote (

L->R

) and remote 

to local (

R->L

), or P1 to P2 (

P1->P2

) and P2 to P1 (

P2->P1

).  

TX Rate

 indicates the transmission rate for each step. 

SLA Verified

 indicates the committed SLA parameters that are used to 

declare the pass/fail verdict. See 

Summary (EtherSAM)

 on page 485 for 

more information on 

Frame Loss Rate

, 

Max Jitter

, 

Round-Trip 

Latency

, and 

Max RX Rate

. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands