manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 331

Test Setup - Test Configurator, Timer, and System

Power Blazer

319

Streams - Profile

Shaping 

TX Mode

 allows the selection of the transmission mode for the 

selected stream when 

Data

 profile is selected. The TX Mode is forced 

to 

Continuous

 for Voice and Video profiles and when using 

Provider 

Encapsulation

. 

TX Rate

 / 

Max TX Rate

 indicates the transmission rate for Voice and 

Video profiles, and allows entering the transmission rate for Data 
profile. The available stream transmission rate will be calculated 
according to the selected TX Mode. The default setting is 100 percent 
for all interfaces at the exception of 10Gig-E WAN which is 92.8571 
percent (depending on the frame format). 

Unit choices are: 

%

 (default), 

Mbit/s

, 

Gbit/s

, 

frame/s

, 

IFG

. However 

frame/s

 and 

IFG

 are not available for 

Random

 and 

Sweep

 frame sizes. 

Continuous

 (default) transfers the 

selected frame continuously according to 
the selected percentage of bandwidth. 

n-Frame

 transfers the selected number of 

frames. 

Burst

 transfers the selected frame at 

maximum bandwidth for the selected 

Burst Duty Cycle

 over the 

Period

. 

n-Burst 

transfers the selected number of 

Burst. 

Ramp

 transfers the selected bandwidth in 

a stair shape according to the selected 
step time, number of steps, and maximum 
bandwidth. 

n-Ramp

 transfers the selected number of 

Ramp. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands