manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 367

Test Results

Power Blazer

355

Alarms/Errors Overview

E1 

Note:

For Wander test application only 

AIS

 and 

LOF

 alarms are supported. 

Alarms

Note:

Only AIS is available when the framing is set to 

Unframed

.

AIS

 (Alarm Indication Signal) 

RX

: Two or less ZEROs are received in each of two consecutive double 

frame periods (512 bits). 

LOF

 (Loss Of Frame) 

RX

: Three consecutive incorrect frame alignment signals is received.

RAI 

(Yellow) (Remote Alarm Indication) 

RX

: Bit 3 in timeslot 0 is set to “1”.

TS16 AIS

 (TimeSlot 16 Alarm Indication Signal) 

RX

: Three or less ZEROs are received in each Timeslot 16 of two 

consecutive multiframes. 

LOMF

 (Loss Of MultiFrame) 

RX

: Two consecutive multiframes alignment signals (bits 1 through 4 of 

TS16 of frame 0) is received with an error.

RAI MF

 (Remote Alarm Indication Multi-Frame) 

RX

: Bit 6 of timeslot 16 of frame 0 is set to “1”.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands