manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 391

Test Results

Power Blazer

379

Alarms/Errors Overview

FSF

 (Forward Signal Fail) 

RX

: The FTFL byte 0 is “00000001”.

TX

: Generates a “00000001” pattern in the FTFL Byte 0 continuously.

LCK

 (Lock) 

RX

: STAT information in the PM byte 3, bits 6 to 8 is “101” for at least 3 

consecutive frames.

TX

: Generates a repeating "01010101" pattern in the entire ODUk signal, 

excluding the frame alignment overhead (FA OH) and OTUk overhead 
(OTUk OH).

LOFLOM

 (Loss of Frame Loss Of Multiframe) is only available for 

mapped ODU client signal (designated as LO in the standard).

RX

: OOF is present for at least 3 ms.

TX

: Generates error continuously in FAS and MFAS of a multiplexed 

test case.

OCI

 (Open Connection Indication) 

RX

: STAT information in the PM byte 3, bits 6 to 8 is “110” for at least 3 

consecutive frames.

TX

: Generates a repeating "01100110" pattern in the entire ODUk signal, 

excluding the frame alignment overhead (FA OH) and OTUk overhead 
(OTUk OH).

TIM

 (Trace Identification Mismatch) 

RX

: The received SAPI and/or DAPI do not math the expected SAPI 

and/or DAPI. This alarm is only available when the SAPI ODU-TIM 
and/or DAPI ODU-TIM check boxes are selected from 

PT / Global PT

 on 

page 179.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands