manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 252

Test Setup - Test Configurator, Timer, and System

240

88000 Series

ODU Channels - Global

Channel Summary 

Channel ID / Type

 table indicates each channel number with its ODU 

mapping type. 

Payload Type

 indicates the mapped ODU payload type. 

Quantity of Channels

 indicates the number of channels part of the 

test. 

Unused Capacity

 indicates the number of tributary slot not used; 

either configured as background traffic or Unallocated. 

Modify Trib Slots/Channels

 

Channel ID

 selects a channel number highlighting the tributary 

slots composing this channel. Alternatively, selecting a channel 
from the table on the right (

TX

, 

RX

, or 

TX = RX

 tab) also selects a 

channel number. 

Tributary Port

 indicates the tributary port

 

number associated to 

the channel number. 

Payload Type

 indicates the payload type for the mapped OPU. 

RX

, 

TX

, or 

TX = RX

 tab (table on the right) displays the tributary 

slot assignments per channel for either RX, TX, or both RX and TX 
(TX=RX) and allows selecting tributary slots to be 
assigned/unassigned; see 

Assign

/

Unassign

/

Mode

 for more 

information. 

Each tributary slot displays its number (left top corner) and 
channel number (middle); the channel number is replaced by 

B

 or 

U

 indicating respectively if the tributary slot carries background 

traffic or is configured as Unallocated. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands