manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 155

Test Setup - Test Configurator, Timer, and System

Power Blazer

143

BERT and Unframed BERT

Note:

The Service Disruption Time measurement supports a parent defect 
approach where the SDT measurement is triggered when the selected 
defect or a higher defect in the signal structure hierarchy is detected. For 
example, if Bit Error is selected, an OPU AIS error will trigger an SDT event. 

No Defect Time (ms)

 represents the period without any defects before 

stopping SDT measurement: 

0.005 ms

 to 

2000 ms

 (default is 

300 ms

). 

Disruption Monitoring

 check box when selected (disabled by 

default) enables the disruption time measurements. However, the 
measurement will only start if the test is already started, or when the 
test will be started. 

STS/AU Path  AIS-P/AU-AIS

, 

LOP-P/AU-LOP

, 

RDI-P/HP-RDI

, 

REI-P/HP-REI

, 

B3

,

 UNEQ-P/HP-UNEQ

, 

PDI-P (SONET)

VT/TU Path  AIS-V/TU-AIS

, 

LOP-V/TU-LOP

, 

UNEQ-V/LP-UNEQ

, 

RDI-V/LP-RDI

, 

REI-V/LP-REI

, 

BIP-2

DS1 AIS

,

 OOF

,

 RAI

,

 Framing Bit

,

 CRC-6

DS3 AIS

,

 OOF

,

 Idle

,

 RDI

,

 F-Bit

,

 C-Bit

,

 P-Bit

,

 FEBE

E1 AIS

, 

CRC-4

, 

E-Bit

, 

LOMF

,

 TS16 AIS

,

 LOF

,

 FAS

,

 RAI

,

 RAI MF

E4

, 

E3

, 

E2

 

AIS

, 

LOF

, 

FAS

, 

RAI

OTL

b

LOF

, 

OOF

, 

LOL

, 

LOR

, 

OOR

, 

Inv. Marker

, 

FAS

FEC

FEC CORR

, 

FEC UNCORR

OTUk

c

AIS

, 

LOF

, 

OOF

, 

LOM

, 

OOM

, 

BDI

, 

IAE

, 

BIAE

, 

BIP-8

, 

BEI

, 

FAS

, 

MFAS

ODUk

c

AIS

, 

OCI

, 

LCK

, 

BDI

, 

BIP-8

, 

BEI

, 

FSF

, 

BSF

, 

FSD

, 

BSD

OPUk

c

AIS

, 

CSF, PLM

d

, MSIM

e

, LOOMFI

e

f

, OOMFI

ef

, OMFI

ef

BER

g

Pattern Loss

, 

Bit Error

 (default)

a.

Not available with QSFP transceivers. 

b.

The service disruption time measurement is available per lane for OTL defects at the exception of LOL

which is global for all lanes. Refer to 

OTL-SDT

 on page 437 for results per lanes.

c.

Only available on the top layer.

d.

Available when the PLM check box is selected (refer to page 180 for more information).

e.

Available with multiplex test only.

f.

Available with OPU4 only.

g.

Available when the 

No Pattern Analysis (Live) 

check box (see page 139) is cleared.

Layer

Defect

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands