manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 329

Test Setup - Test Configurator, Timer, and System

Power Blazer

317

Streams - Profile

Frame Size (Bytes)

 for Data profile is selectable: 

Fixed

 (default), 

Random

, or 

Sweep

. The Frame Size is forced to 

Fixed

 for Voice and 

Video profiles. Only 

Fixed

 frame size is available when using 

Provider 

Encapsulation

.

For 

Fixed

 type, the frame size is as follow. 

For 

Random

 type, the frame size range is from 64 to 1518 bytes. 

However, the minimum frame size will be adjusted according to 
the frame structure and components selected. The following table 
lists each component that may affect the minimum frame size 
value. The maximum frame size value is also adjusted for VLAN 
(+4 bytes per VLAN). 

Profile

Codec

Frame Size

IPv4

IPv6

Voice

VoIP G.711

138

158

VoIP G.723.1

82

102

VoIP G.729

78

98

Video

All codec

1374

1394

Data

-

Programmable from 

64

a

 to 

16000

b

a.

The minimum frame size will be adjusted according to the frame structure and

components selected. The following table lists each component that may

affect the minimum frame size value. 

b.

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands