manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 632

Test Functions

620

88000 Series

RTD

RTD 

Note:

Available with Pattern client. Not available in Decoupled, Through, or 
Through Intrusive mode. 

Round Trip Delay (RTD) measurements are needed to quantify the time it 
takes for a signal to cross the network and come back. Usually, transport 
delay is due to two factors: long configured paths and transit times through 
the network elements along the path. Therefore, RTD measurements are 
significant in systems that require two-way interactive communication, 
such as voice telephony, or data systems where the round-trip time directly 
affects the throughput rate.

From the 

Test

 menu, tap 

Functions

, and the 

RTD

 tab. 

Note:

To do a Round Trip Delay test, the remote NE should be configured to 
provide a loopback.  

Note:

Be aware that RTD requires error free operation conditions to provide 
reliable results. Therefore, RTD results could be affected by error injection 
or error introduced by the network.

Mode

Allows the selection of the round trip delay test mode. Choices are 

Single

 

(default) and 

Continuous

.  

Single 

allows testing the round trip delay once. 

Continuous

 allows testing the round trip delay continuously in a 

repetitive manner (one RTD measurement every 2 seconds). 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands