manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 143

Test Setup - Test Configurator, Timer, and System

Power Blazer

131

Signal Auto-Detect

Signal Auto-Detect 

The Signal Auto-Detect allows the detection of the DS1/DS3 interface 

Line Coding

 (DS1), 

Framing

, and 

Test Pattern

. 

Signal Auto-Detect

 is only available: 

with DS1 and DS3 interfaces. 

when the test is stopped. 

when Loopback is not activated for NI/CSU Emulation test. 

Note:

Test Pattern is not detected with NI/CSU Emulation test application. 

During the detection process, the following messages may be displayed: 

Detecting

, 

Successful

, and/or 

Failed

. 

When the auto-detection is successful, the detected parameters are 
automatically applied as the test interface configuration. 

Upon detection of specific alarms, the detection may not be possible, tap 

Retry

 to invoke the detection again. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands