manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 246

Test Setup - Test Configurator, Timer, and System

234

88000 Series

Network Details (iSAM)

Each profile entry has the following parameters. 

Profile Name

: 1 to 16 characters. All ASCII characters from 32 to 126 

decimal are supported. 

Frame Type

: Enter 

Fixed

 or 

EMIX

. When the frame type is missing 

from a profile, 

EMIX

 is used.

Frame Size

 (see 

Frame Size

 on page 230 for possible values); when 

the frame size is missing from a profile, default value(s) is used: 
For 

Fixed

: Enter a unique frame size. 

For 

EMIX

: Enter 2 to 8 frame sizes with a comma between each entry. 

VLAN Priority

1

 (optional): Enter the priority number.

DSCP

1

 (optional): Enter either the DSCP name or its binary value. 

Performance Criteria

1

: Enter the name of the performance criteria. 

When the 

Performance Criteria

 is missing from a profile or is not 

available from the user profile file, the 

User Performance

 criteria is 

used. 

When a parameter is missing from a profile, the default value of the 
missing parameter is used. 

The value of a parameter is validated to ensure it is within the supported 
range; otherwise the profile entry is unsupported. 

If the profile file contain more than 25 profiles, only the first 25 valid profiles 
are retained. 

1. See 

Classification

 on page 231 for possible values. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands