manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 414

Test Results

402

88000 Series

Alarms/Errors Overview

TCM (SONET/SDH) 

Note:

TCM is displayed for rates up to OC-192/STM-64 under the STS-x/AU-x or 
VT/TU alarms/errors group when TCM is enabled.

Alarms

TC-UNEQ-P

 / 

HPTC-UNEQ (

Unequipped) 

RX/TX

: An all “0”s pattern is received/generated in the higher order 

path signal label byte (C2), the TCM byte (N1) and the path trace byte 
(J1), and a valid BIP-8 bytes (B3).

TC-UNEQ-V

 / 

LPTC-UNEQ 

(Unequipped)

(LPTC - Unequipped) 

RX/TX

: An all “0”s pattern is received/generated in the lower order path 

signal label (bit 5, 6, 7 of byte V5), the TCM byte (Z6/N2) and the path 
trace byte (J2), and a valid BIP-2 (bits 1, 2 of V5 byte).

TC-LTC-P / TC-LTC-V

 / 

HPTC-LTC / LPTC-LTC

 (Loss of Tandem 

Connection) 

RX/TX

: A wrong FAS multiframe is received/generated.

TC-IAIS-P

 / 

HPTC-IAIS

 (Incoming Alarm Indication Signal) 

RX/TX

: Bits 1 through 4 of the N1 byte are set to “1110”.

TC-IAIS-V

 / 

LPTC-IAIS 

(Incoming Alarm Indication Signal) 

RX

/

TX

: Bit 4 of the Z6/N2 byte is set to “1”.

TC-ODI-P / TC-ODI-V

 / 

HPTC-ODI / LPTC-ODI 

(Outgoing Defect 

Indication) 

RX/TX

:

SONET: Bit 7 of the N1/Z6 byte frame 74 is set to “1”.

SDH: Bit 7 of the N1/N2 byte multiframe 74 is set to “1”.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands