manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 266

Test Setup - Test Configurator, Timer, and System

254

88000 Series

RFC 2544 - Global

Frame Size (Bytes):

 For 

RFC 2544

 distribution, gives predefined frame 

size distribution values. For 

User Defined

 distribution, enter up to 

seven frame size values. 

The following table lists each component that may affect the minimum 
size value.

Restore RFC 2544 Defaults 

Reverts the configured parameters to their default values. 

Distribution

Frame Size

RFC 2544

64

a

,

128

, 

256

, 

512

, 

1024

, 

1280

, and 

1518

a.

The minimum frame size will be adjusted according to the frame structure and

components selected.

User Defined

64

a

 to 

16000

b

b.

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface.

Component

Description

VLAN

4 bytes per VLAN tag (up to 3 VLAN tags) 

LLC and SNAP Headers

8 bytes

IPv4

20 bytes

IPv6 40 

bytes

Using DTS

4 bytes

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands