manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 729

Glossary

Power Blazer

717

G.709 Optical Transport Network (OTN)

Optical Transport Unit (OTU) 

The OTU overhead is comprised of the SM, GCC0 and RES bytes.

The section monitoring (SM) bytes are used for the trail trace 
identifier (TTI), parity (BIP-8) and the backward error indicator 
(BEI), or backward incoming alignment error (BIAE), backward 
defect indicator (BDI), and incoming alignment error (IAE). The 
TTI is distributed over the multiframe and is 64 bytes in length. It is 
repeated four times over the multiframe. 

General communication channel 0 (GCC0) is a clear channel used 
for transmission of information between OTU termination points. 

The reserved (RES) bytes are currently undefined in the standard. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands