manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 271

Test Setup - Test Configurator, Timer, and System

Power Blazer

259

RFC 2544 - Subtests

Frame Loss Configuration 

The objective of this test is to find the percentage of frames that are lost 
due to lack of resources. Starting at the specified maximum rate (

Max. 

Rate

), the test is performed for a specific frame size and for the specified 

duration 

(Trial Duration)

. The test is repeated by decreasing the rate by 

the specified granularity (

Granularity

), then the test is repeated again until 

there are two successive trials in which no frames are lost. The test is 
performed for the defined number of trials (

Trials

). The test is performed 

for each defined frame size. 

Max. Rate

 is the maximum rate the test should begin with, in terms of 

a percentage of the line rate (

%

), 

Mbit/s

, or 

Gbit/s

. The accepted 

values are as shown in the Max. Rate table on page 256. For 

Dual Test 

Set

, 

Max. Rate

 is configurable for both local to remote (

L->R

) and 

remote to local (

R->L

) directions. For 

Dual Port

 topology, Max. Rate is 

configurable for both P1 to P2 (

P1->P2

) and P2 to P1 (

P2->P1

) 

directions. 

Trial Duration

 represents the time value for each trial in 

minutes:seconds: 

1

 second to 

30 

minutes (default is 

00:01

). 

Trials

 represents the number of times the test will be generated: 

1

(default) to 

50

 trials. 

Granularity

 corresponds to the percentage interval between each 

throughput value used for the test: 1 % to 10 % (RFC) - (default). For 
example, 10 % granularity means that the test will be performed for 
100 %, 90 %, 80 %... of the rate value. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands