manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 145

Test Setup - Test Configurator, Timer, and System

Power Blazer

133

1588 PTP

GM IP Address

1

 is the IP address of the Grand Master Clock used by 

the 1588 PTP function to communicate with it. 

Quick Ping

1

 button allows testing if the Grand Master IP address can 

be reached. A message is returned indicating if the ping attempt was 

Successful

 or 

Failed

. 

IP

 

TOS/DS

1

 allows entering the Type of Service: 

0x00

(default) to

0xFF

. 

Mechanism

 is not selectable and is set to 

Delay Req-Resp

 (Delay 

Request-Response) which specifies the mechanism used by the 
1588 PTP function to communicate with the Grand Master clock. Refer 
to 

Delay Request-Response

 on page 697 for more information. 

Delay Mode

 is not selectable and is set to 

Two-way

 which uses 

Sync/Follow Up, Delay Request, and Delay Response messages. 

Connect

1

 button is used to initiate the Grand Master Connection 

process. This process is also automatically initiated when starting the 
test if not already initiated. The process automatically ends when 
stopping the test. 

Negotiation Status

1

 is displayed during the Unicast negotiation 

process which is initiated when either the test is started or the 

Connect

 

button is activated. See 

Negotiation Status

 on page 475 for more 

information. 

1. Only available with Unicast mode. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands