manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 175

Test Setup - Test Configurator, Timer, and System

Power Blazer

163

EtherSAM - Burst

EtherSAM - Burst 

Note:

The 

Burst

 settings are only available for configuration when the 

Burst Test

 

check box is selected (see page 165). 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, tap on the test block, 

and on the 

Burst

 tab. 

Note:

The burst configuration parameters are defined globally for all services but 

CBS

, 

EBS

, and 

Burst Max Rate

 parameters are as per each service 

configuration. 

Burst Sequence

The graphic illustrates the configured burst sequence that contains in 
order, from left to right: 

Refill Delay

 represents the pre-burst recuperation time in percentage 

that is equal to the remaining percentage not used by the post-burt 
time (

Refill Delay Ratio

). 

Burst Frames

 represents the burst frame ratio in percentage that is 

equal to the substraction of 

100 % - Burst/IR Frame Ratio

. 

Refill Delay

 represents the post-burst recuperation time in percentage 

that is equal to the configured 

Refill Delay Ratio

. 

CIR or CIR+EIR Frames

 represents the percentage of transmission at 

CIR or CIR+EIR rate. The 

CIR or CIR+EIR Frames

 percentage is equal 

to the configured 

Burst/IR Frame Ratio

. 

The “. . .” next to the burst sequence indicates that the burst sequence 
is repeated the number of times specified in the 

Number of Burst 

Sequence

 field.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands