manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 132

Test Setup - Test Configurator, Timer, and System

120

88000 Series

Modify Structure Button

For Ethernet Test Applications 

Port 1

 and 

Port 2

 are only displayed when 

Dual Port

 topology is 

selected and allows configuring each port individually. 

Interface/Rate

 choices depend on the selected test and the rates 

available on the module. 

Test

Interface/Rate

EtherSAM

 

RFC 2544
RFC 6349
EtherBERT
Traffic Gen & Mon
Smart Loopback

 

400GE

 (8 Lanes) [425 Gbit/s]

a

 

100GE (4 Lanes) [103.125 Gbit/s] 
40GE (4 Lanes) [41.25 Gbit/s] 
25GE

b

 

10GE WAN

c

 

10GE LAN 
1GE Optical 
100M Optical 
10/100/1000M Electrical

d

 

a.

Only available for EtherBERT. 

b.

Only available for RFC 2544, EtherBERT, Traffic Gen & Mon, and Smart Loopback. 

c.

Not available with RFC 6349 test application. 

d.

Also available as a second port when the test application requires two ports;

Ethernet 10/100/1000 Mbit/s electrical is supported when using an active copper

SFP. 

Carrier Ethernet OAM

 

10GE WAN 
10GE LAN 
1GE Optical

 

100M Optical 
10/100/1000M Electrical

Through Mode

100GE (4 Lanes) [103.125 Gbit/s]

e

 

10GE LAN

 

1GE Optical 
100M Optical 
10/100/1000M Electrical

f

 

e.

Only supported on the 88200NGE.

f.

Ethernet 10/100/1000 Mbit/s electrical is supported when using an active copper

SFP and the RJ45 port. 

TCP Throughput

1GE Optical 
100M Optical 
10/100/1000M Electrical

 

Cable Test

10/100/1000M Electrical

 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands