manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 198

Test Setup - Test Configurator, Timer, and System

186

88000 Series

Interface (Ethernet, Packet Sync, Fibre Channel, and Wireless)

For Fibre Channel test application: 

PSP (Link Protocol)

 (Primitive Sequence Protocol) check box when 

selected (default) allows link management by activating the port. 

For CPRI 

Unframed

 test application: 

Scrambling

 check box when selected (default) enables the scrambler. 

Only available with CPRI rates 4.9152 Gbit/s and higher. 

For CPRI 

Framed L2

 test application: 

Sequence

 indicates the last Startup Sequence State: 

Standby (A)

, 

L1 Sync (B)

, 

Protocol (C)

, 

L2 C&M (D)

, 

Vendor (E)

, 

Operation (F)

, 

or 

Passive (G)

. 

Frame Sync

 indicates the synchronization status: green 

for active, red for inactive, or gray for pending. 

Protocol

 defines how the CPRI Startup Sequence negotiates the 

protocol version. 

Auto

 can use protocol 

Version 1

 and 

Version 2

 during the 

negotiation. 

Version 1

 negotiates the protocol with Scrambling disabled. 

Available with all supported CPRI rates. 

Version 2

 negotiates the protocol with Scrambling enabled. 

Available with CPRI rates: 9.8, 6.1, and 4.9 Gbit/s. 

Protocol

 table indicates either the last received (

Version 1

 or 

Version 2

) or negotiated (

Auto

) protocol version. A light-red 

background indicates a Protocol version mismatch between the 
received value and the expected generated value. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands