manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 398

Test Results

386

88000 Series

Alarms/Errors Overview

OTUx 

Note:

Available for OTU4, OTU3, OTU3e1, OTU3e2, OTU2, OTU2f, OTU1f, OTU2e, 
OTU1e, and OTU1.

Alarms

AIS

 (Alarm Indication Signal) available with serial interfaces only. 

RX

: Polynomial number 11 (PN-11) is over all OTU frame bits including 

FAS and MFAS for at least 3 consecutive 8192 bit-interval.

TX

: Generates polynomial number 11 (PN-11) over all OTU frame bits 

including FAS and MFAS continuously.

BDI

 (Backward Defect Indication) 

RX

: The BDI bit in the SM overhead field (byte 3, bit 5) is “1” for at least 

5 consecutive OTU frames. 

TX

: Generates “1” for the BDI bit in the SM overhead field (byte 3, bit 5) 

continuously.

BIAE

 (Backward Incoming Alignment Error) 

RX

: The BEI/BIAE bits in the SM overhead field (byte 3, bits 1 to 4) are 

“1011” for at least 3 consecutive frames. 

TX

: Generates “1011” for the BEI/BIAE bits in the SM overhead field 

(byte 3, bits 1 to 4) continuously.

IAE

 (Incoming Alignment Error) 

RX

: The IAE bit in the SM overhead field (byte 3, bit 6) is “1” for at least 

5 consecutive OTU frames. 

TX

: Generates “1” for the IAE bit in the SM overhead field (byte 3, bit 6) 

continuously.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands