manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 655

Test Control

Power Blazer

643

Lpbk Tool Button (Loopback Tool)

S-OAM Responder

 check box when selected (default) allows 

responding to LBM, LTM, DMM, LMM, and SLM valid messages 
(

Lpbk Tool

 must be started, see 

Loopback

 button below). Traffic 

statistics are also monitored (refer to 

Responder

 on page 535). 

Responder - TX Count

 reports respectively the count of LBR, LTR, 

DMR, LMR, SLR, and the total of frames transmitted. 

Responder - RX Count

 reports counts of valid LBM, LTM, DMM, 

LMM, SLM, and the total of frames received. A valid messages must 
have its destination MAC address matching either the unit port 
Unicast MAC address or a Multicast class 1 address

1

. 

Loopback

 button starts/stops looping back the frames/packets that are 

received. The default value is disabled. 

Responds to... message

Responds with... message

LBM

LBR

LTM

LTR

DMM

DMR

LMM

LMR

SLM

SLR

1. Refer to 

Unicast/Multicast Addresses for Ethernet OAM

 on page 757 for more information.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands