manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 638

Test Functions

626

88000 Series

S-OAM Link Trace

S-OAM Link Trace 

From the

 Test

 menu, tap 

Functions

, and the 

S-OAM Link Trace

 tab. 

Link Trace 

Priority

1

 allows selecting the VLAN user priority: 

0

 (default) to 

7

. Refer 

to 

VLAN ID and Priority

 on page 758 for more information. 

Drop Eligible

1

 is set to 

No

 (no frames will be dropped when 

congestion occurs) and is not configurable. 

TTL

 sets the Time To Live value: 

1

 to 

255

 (default is 

128

). 

Link Trace

 button when ON (OFF by default) starts the link trace 

process. The 

Link Trace

 button turn OFF automatically once the link 

trace process is completed. 

Result 

The table reports the following information for each valid LTR frames 
received in response to the last LTM frame sent: 

TTL

, 

MEP/MIP MAC 

Address

, 

Forward

, and 

Term MEP

. 

Last Link Trace Status 

displays the last link trace status. 

TX LTM

 indicates the count of transmitted LTM frames. 

1. Available when VLAN is enabled (see 

VLAN

 on page 225). 

Status

Description

Pending

No Results

Successful

Last Link Trace was successful

Failed – LTR Timeout

Last Link Trace failed due to a LTR Timeout

Failed – Invalid LTR

Last Link Trace failed due to an Invalid LTR

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands