manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 192

Test Setup - Test Configurator, Timer, and System

180

88000 Series

FTFL/PT and PT

Note:

The 

Code

 field is automatically updated when the 

Payload Type

 is 

changed and vice versa.

OPU-PLM

, when selected, enables the OPU-PLM alarm analysis. 

OC-12/STM-4 into ODU0

0B

0000

1011

FC-100 into ODU0

0C

0000

1100

FC-200 into ODU1

0D

0000

1101

FC-400 into ODUflex

0E

0000

1110

FC-800 into ODUflex

0F

0000

1111

Bit Stream with Octet Timing mapping

10

0001

0000

Bit Stream Without Octet Timing mapping

11

0001

0001

IB SDR mapping into ODUflex

12

0001

0010

IB DDR mapping into ODUflex

13

0001

0011

IB QDR mapping into ODUflex

14

0001

0100

ODU Multiplex with ODTUjk

20

0010

0000

ODU Multiplex with ODTUk.ts/ODTUjk

21

0010

0001

Not Available

b

55

0101

0101

Reserved Codes for Proprietary Use

c

80

1000

0000

NULL Test Signal mapping

FD

1111

1101

PRBS Test Signal mapping

FE

1111

1110

a.

Selecting 

Reserved for International Standardization

 will use the hexadecimal code 00 but, all codes

not listed in the previous table at the exception of those covered in notes b and c are reserved for future

standardization.

b.

Selecting 

Not Available

 will use the hexadecimal code 55 but, 66 and FF are also Not Available payload

types.

c.

Selecting 

Reserved Proprietary

 will use the hexadecimal code 80 but, all codes from 80 to 8F are

reserved proprietary payload types.

Payload type

Hex Code

MSB

1234

LSB

5678

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands