EXFO Power Blazer 88000 Series User Manual Download Page 569

Page: 569 / 803

Test Functions

Power Blazer

557

FDL - Bit-Oriented Message

Codeword

Command/Response

Codeword

Pattern

Command/Response

Codeword

Pattern

Line Loopback Activate

00001110 11111111 Protection Switch Line 22

01101100 11111111

Line Loopback Deactivate

00111000 11111111 Protection Switch Line 23

01101110 11111111

Payload Loopback Activate

00010100 11111111 Protection Switch Line 24

01110000 11111111

Payload Loopback Deactivate 00110010 11111111 Protection Switch Line 25

01110010 11111111

Reserved for Network Use

00010010 11111111

Loopback Activate.

Protection Switch Line 26

01110100 11111111

Universal Loopback
(Deactivate)

00100100 11111111 Protection Switch Line 27

01110110 11111111

ISDN Line Loopback (NT2)

00101110 11111111 Protection Switch Acknowledge 00011000 11111111

CI/CSU Line Loopback (NT1)

00100000 11111111 Protection Switch Release

00100110 11111111

For network use

00011100 11111111

Indication of NT1 power off.

Do Not use for Synchronization 00110000 11111111

Protection Switch Line 1 b

01000010 11111111 Stratum 2 Traceable

00001100 11111111

Protection Switch Line 2

01000100 11111111 SONET Minimum Clock

Traceable

00100010 11111111

Protection Switch Line 3

01000110 11111111 Stratum 4 Traceable

00101000 11111111

Protection Switch Line 4

01001000 11111111 Stratum 1 Traceable

00000100 11111111

Protection Switch Line 5

01001010 11111111 Synchronization Traceability

Unknown

00001000 11111111

Protection Switch Line 6

01001100 11111111 Stratum 3 Traceable

00010000 11111111

Protection Switch Line 7

01001110 11111111 Reserved for Network

Synchronization

01000000 11111111

Protection Switch Line 8

01010000 11111111 Transmit Node Clock (TNC)

01111000 11111111

Protection Switch Line 9

01010010 11111111 Stratum 3E Traceable

01111100 11111111

Protection Switch Line 10

01010100 11111111 Under study for maintenance

00101100 11111111

Protection Switch Line 11

01010110 11111111 Under study for maintenance

00110100 11111111

Protection Switch Line 12

01011000 11111111 Reserved for network use

00010110 11111111

Protection Switch Line 13

01011010 11111111 Reserved for network use

00011010 11111111

Protection Switch Line 14

01011100 11111111 Reserved for network use

00011110 11111111

Protection Switch Line 15

01011110 11111111 Reserved for network use

00111010 11111111

Protection Switch Line 16

01100000 11111111 Reserved for customer

00000110 11111111

Protection Switch Line 17

01100010 11111111 Reserved for customer

00001010 11111111

Protection Switch Line 18

01100100 11111111 Reserved for customer

00000010 11111111

Protection Switch Line 19

01100110 11111111 Reserved for customer

00110110 11111111

Protection Switch Line 20

01101000 11111111 Reserved for customer

00111100 11111111

Protection Switch Line 21

01101010 11111111 Reserved for customer

01111010 11111111

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands