manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 291

Test Setup - Test Configurator, Timer, and System

Power Blazer

279

Services - Global

Total TX Rate 

Note:

Only available when the 

Service Performance Test

 check box is selected 

(see 

EtherSAM - Global

 on page 165). For 

Dual Test Set

, the total TX rates 

are displayed for both 

Local

 and 

Remote

 directions.

Committed

 displays the total enabled TX rate (bandwidth) that will be 

generated by the selected service(s). 

Available

 displays the total TX rate (bandwidth) available for traffic 

generation. 

Global Options 

Rate Unit

 choices are 

%

 (default), 

Mbit/s

, and 

Gbit/s

.

Copy Service Button 

Copy Service

 button allows copying the services configuration to one or 

several services. 

Copy Service

 allow selecting the services number from which the 

configuration will be copied from. 

To the following Services

 allows selecting all services that will inherit 

the configuration from the selected service. An orange background 
represents a selected service. A service that is already enabled cannot 
be selected for copy. 

Copy

 allows confirming the service configuration copy for all selected 

services. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands