manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 539

Test Results

Power Blazer

527

Traces - SONET/SDH

Traces - SONET/SDH 

From the 

Test

 menu, tap 

Results

, 

Traces

, and the 

SONET/SDH

 sub-tab. 

Note:

Selecting a Trace byte to be generated will automatically update the 
corresponding OH byte. Refer to 

OH - SONET/SDH

 on page 591 for more 

information.

Traces 

Section/RS (J0)

, and 

STS/AU/TU-3 Path (J1)

, and 

VT/TU Path (J2) 

Displays the received J0/J1/J2 value in 16 or 64-bytes format. The 
<crc7> represents the CRC-7 for a 16-bytes format. The last two bytes 
of a 64-bytes format, <C

R

> and <L

F

>, represent respectively a 

carriage return and a line feed.

TIM-S/RS-TIM

,

 TIM-P/HP-TIM

, 

TIM-V

/

LP-TIM

: Enables the 

corresponding Trace Identifier Mismatch for the expected message 
defined. These settings are coupled with the Traces configuration from 

Traces (SONET/SDH)

 on page 336. 

Copy RX

 allows using the received TIM message as the expected one. 

TCM Access Point Identifier 

Note:

Available when TCM is enabled (refer to page 307).

STS/AU Path (N1)

, and 

VT/TU Path (Z6 or N1 (TU-3)) 

Displays the received N1/Z6 value. 

TC-TIM-P/HPTC-TIM/TC-TIM-V/LPTC-TIM

: Enables the corresponding 

TCM Access Point Identifier for the expected message defined. These 
settings are coupled with the Traces configuration from 

Traces 

(SONET/SDH)

 on page 336. 

Copy RX

 allows using the received TIM message as the expected one. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands