manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 425

Test Results

Power Blazer

413

Alarms/Errors Overview

Inject Button 

Layer

: Allows selecting on which layer is the alarm/error to be 

generated. Choices depend on the test application and its interface. 
For Multi-Channel OTN using mix-mapping, 

ODUk

 and 

OPUk

 represent 

ODU and OPU levels of the selected channel(s). 

Port 1

 or 

Port 2

 selection, available with 

Dual Port

 topology, allows 

selecting the port used for alarm/error injection. 

Channel

, available with Multi-Channel OTN, allows selecting the 

channel number that will be used for injection. The 

All

 button selects 

all defined channels. 

Type

: Allows selecting the type of injection, either 

Alarms

 or 

Errors

. 

Defect

: Allows the selection of the alarm/error defect to be generated. 

Choices depend on the selected 

Layer

 and 

Type

. Refer to 

Alarms/Errors

 on page 346 for more information. 

Mode

 and 

Rate/Amount 

Note:

Only 

Manual

 mode is available with 100GE - 

4 Unframed CAUI-4

 and 

OTU4 - 

4 Unframed Physical Lanes

 on 88220NGE; the amount is fixed to 1; 

Pattern Loss injection is not possible. 

Open/Close pop-up button

Selected Alarm/Error

and status

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands