manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 212

Test Setup - Test Configurator, Timer, and System

200

88000 Series

Local Details (iSAM)

Local Details (iSAM) 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and the 

More

 button 

from the 

Local

 block. 

LINK 

An arrow is used to indicate the status of the test link (at the PCS level 
for parallel interfaces). 

A green arrow indicates that the link is up. 

A red arrow indicates that the link is down. 

A gray arrow indicates awaiting incoming data to provide a status. 

Interface/Rate

 or 

Port

 choices depend on the rates available on the 

module. 

For 10GE WAN, the test uses the WIS default values for J0, J1, and C2 as 
defined in 

WIS Button

 on page 191. 

PHY Type

 allows selecting the 100GE (4 Lanes) CFP4/QSFP transceiver 

PHY type: 

LR4/ER4

(default), 

SR4

, 

CWDM4

, 

CLR4

, or 

Other

. The PHY 

type when set to any except 

LR4/ER4

, allows enabling RS-FEC (see 

page 182); ensure both ends of the circuit have the FEC enabled. Only 
available with 100GE (4 Lanes) framed Ethernet interface. 

100GE (4 Lanes) [103.125 Gbit/s] 
40GE (4 Lanes) [41.25 Gbit/s] 
10GE WAN 
10GE LAN 
1GE Optical 
100M Optical 
10/100/1000M Electrical

a

 

a.

For 88200NGE, only possible when using an active copper SFP. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands