manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 169

Test Setup - Test Configurator, Timer, and System

Power Blazer

157

EtherBERT, FC BERT, BERT (CPRI/OBSAI), and Unframed BERT

BER Threshold

 allows entering the threshold 

Count

 or 

Rate 

value that 

will be used to declare the pass/fail verdict. 

For 

Count

, enter the maximum bit/pattern error count allowed before 

declaring a fail verdict: 

0

 (default) to 

999999

.

For 

Rate

, enter the maximum bit/pattern error rate allowed before 

declaring a fail verdict: 

1.0E-14

 to 

1.9E-01

. The default value is 

1.0E-12

; 

2.1E-5

 for 

CLR4

 unframed; 

5.0E-5

 for 

SR4

, 

CWDM4

, and 

Other

 

unframed.

CPRI/OBSAI 

Note:

Available with CPRI/OBSAI BERT test application with Framed L2. 

Pass/Fail Verdict

 check box when selected (default) enables the pass/fail 

verdict. A pass verdict is given when the link status is up and no 
CPRI/OBSAI alarm and/or error are recorded for the duration of the test. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands