manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 90

Test Setup - Test Applications

78

88000 Series

FC BERT

FC BERT 

The FC BERT (Fibre Channel BERT) application provides full wire-speed 
traffic generation at the FC-2 layer allowing BER testing for link integrity 
measurements, latency, buffer-to-buffer credit measurements for 
optimization as well as login capabilities. 

Typical Fibre Channel BERT test applications: 

Supported Interfaces/Rates: 1X, 2X, 4X, 8X, 10X, 16X. 

Network

under test

Testing Unit

DUT Loopback

EXFO Module

Network

under test

Testing Unit

Testing Unit

EXFO Module

EXFO Module

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands